NACE NACE-CIP2-001 Test Engine Dumps Training With 100 Questions
NACE-CIP2-001 Questions Pass on Your First Attempt Dumps for CIP Level 2 Certified
NEW QUESTION 56
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Sacking
- B. High-pressure water washing
- C. Acid etching
- D. Stoning
Answer: C
NEW QUESTION 57
Individuals conducting Coating Surveys should:
- A. Always be NACE Level 3 Certified Inspectors
- B. Always be NACE or SSPC Protective coating Specialists
- C. Always be experienced Specification Writers
- D. Always be trained and experienced Coating Industry
Answer: D
NEW QUESTION 58
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 25 double rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 25 single rubs with a saturated cloth.
- D. 50 double rubs with a saturated cloth.
Answer: D
NEW QUESTION 59
Ideally, documentation requirements should be defined:
- A. By the inspector
- B. By the contractor
- C. In the specification
- D. At the pre-job conference
Answer: C
NEW QUESTION 60
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Applicator to decide which one to follow
- B. The Product Data Sheet prevails
- C. It is up to the Inspector to decide which one to follow
- D. The Specification prevails
Answer: D
NEW QUESTION 61
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Enforce the additional requirement
- B. Call your supervisor
- C. Request clarification from the specifier
- D. Ignore the additional requirement
Answer: A
NEW QUESTION 62
Coating application to concrete substrates is:
- A. Not required as Concrete is inorganic
- B. The same as coating steel
- C. More challenging than coating steel
- D. Less challenging, than coating steel
Answer: C
NEW QUESTION 63
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. disposed of properly.
- B. washed with clean potable water prior to Use.
- C. mixed with uncontaminated abrasive
- D. run through the air wash separator.
Answer: A
NEW QUESTION 64
A reinforced coating is
- A. equally resistant to movement and impact as a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. equally resistant to abrasion and impact as a non-reinforced coating.
Answer: C
NEW QUESTION 65
Application of Thermal Spray Coatings requires:
- A. Specialized skills supported by training and experience
- B. The same skills as liquid coatings
- C. No particular skills
- D. The same skills as welding
Answer: A
NEW QUESTION 66
It is always possible to see moisture on a steel substrate:
- A. True
- B. False
Answer: B
NEW QUESTION 67
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Coal Tar Enamel
- B. Liquid epoxies
- C. Heat-shrink sleeves
- D. Concrete
Answer: B
NEW QUESTION 68
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very high reading
- B. Cold flow or creep
- C. A very low reading
- D. No difference from any other coating
Answer: B
NEW QUESTION 69
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Magnetic Gauge
- B. Eddy Current Gauge
- C. Ultra Sonic DFT Gauge
- D. Tooke Gauge
Answer: D
NEW QUESTION 70
Inspection and Test Plans are provided to:
- A. Outline the inspection steps, sequencing and pass/fail criteria
- B. So the contractor has a single document to reference
- C. So the Inspector doesn't have to read the entire specification
- D. To supersede the requirements of the product data sheets
Answer: A
NEW QUESTION 71
The main reason dehumidification is used during coating operations is to
- A. control the environment
- B. reduce the possibility of missing the recoat window.
- C. avoid repetitive blasting/coating operations.
- D. allow the contractor to guarantee the completion date.
Answer: A
NEW QUESTION 72
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. True
- B. False
Answer: A
NEW QUESTION 73
Dehumidification is defined as the removal of moisture vapor from the air to
- A. lower its temperature
- B. raise its relative humidity.
- C. lower its dew point,
- D. provide worker comfort.
Answer: C
NEW QUESTION 74
Thermal Spray coatings provide:
- A. Barrier protection
- B. Inhibitive protection
- C. Sacrificial protection
- D. Thermal protection
Answer: C
NEW QUESTION 75
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Document the readings at the end of the shift
- B. Advise the coating applicator supervisor of your readings
- C. Check to See if the dehumidification equipment is operating correctly
- D. Call your supervisor
Answer: B
NEW QUESTION 76
......
NACE-CIP2-001 Practice Test Pdf Exam Material: https://www.examslabs.com/NACE/CIP-Level-2/best-NACE-CIP2-001-exam-dumps.html
NACE-CIP2-001 Answers NACE-CIP2-001 Free Demo Are Based On The Real Exam: https://drive.google.com/open?id=1g38wjPgDlxAcHQCDHKPkklrjGQP4nJWo