HPE6-A72 by HP Valid Free Exam Practice Test

Question 1

Refer to the exhibit.

Using the static IP address configured above, what is the converted binary value of the third octet assigned to the local interface?

A. 11010101 B. 10110001 C. 01001011 D. 11111000

Correct Answer: A

Question 2

Which two options are the Layer 2 protocols? (Choose two.)

A. RIP B. 802.1Q C. STP D. IPSec E. 802.11af

Correct Answer: B,C

Question 3

Refer to the exhibit

Which command on Access-2 port 1/1/4 will enable connectivity between PC-1 and Server-1 without any routing enabled in the network?

A. Access-2 (config-if-1/1/4)# vlan access 20 B. Access-2 (config-if-1/1/4)# vlan 20 untag 1/1/4 C. Access-2 (config-if-1/1/4)# vlan access 1, 10, 20, 255 D. Access-2 (config-if-1/1/4)# vlan trunk allow 1, 10, 255

Correct Answer: A

Question 4

Refer to the exhibit.

What is the correct binary conversion of the last two hexadecimal characters of the physical address?

A. 1001 1111 0101 0011 B. 1101 1000 C. 1110 1101 D. 1000 1101 1110 1101

Correct Answer: C

Question 5

Refer to the exhibit.

What configuration is needed in order for "show LLDP configuration" to show this output?

A. enabling LLDP on the interfaces only B. configuring LLDP globally only C. none; LLDP is enabled by default on Aruba switches D. configuring LLDP both globally and on the interfaces

Correct Answer: C

Question 6

Interface 1/1/1 is up
Admin state is up
Link transitions: 1
Description: TO_PC-1
Hardware: Ethernet, MAC Address: 00:11:22:33:44:55
MTU 1500
Type 1GbT
Full-duplex
qos trust none
Speed 1000 Mb/s
Auto-negotiation is on
Flow-control: off
Error-control: off
MDI mode: MDIX
VLAN Mode: access
Access VLAN: 1111
Which command will produce the above output?

A. show interface 1/1/1 B. show interface gigabit 1/1/1 C. show vlan 1111 D. show interface vlan 1111

Correct Answer: A

Question 7

Refer to the exhibit.

You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master. What is a valid configuration for Access-2 to join the VSF stack?

A. Access-2# configure
Access-2(config)# vsf member 2
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y B. Access-2# configure
Access-2(config)# vsf member 1
Access-2(config)# vsf renumber-to 2
Access-2(vsf-member-1)# link 2 2/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y C. Access-2# configure
Access-2(config># vsf member 2
Access-2(vsf-member-1)# link 2 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y D. Access-2# configure
Access-2(config)# vsf member 1
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
Access-2(config)# vsf renumber-to 2
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

Correct Answer: A

HP Aruba Certified Switching Associate - HPE6-A72 Exam Practice Test