NS0-593 by Network Appliance Valid Free Exam Practice Test

Question 1

A customer reports that some of their client computers are unable to access a FlexGroup over CIFS. This problem involves only their older Windows XP clients and some printers and scanners.
In this scenario, which statement Is correct?

A. FlexGroup requires CIFS shares to use the Continuously Available Feature, which these clients do not support. B. These systems use Offloaded Data Transfer, which is an unsupported feature in FlexGroup. C. FlexGroup requires CIFS shares to be located in qtrees, which these clients do not support. D. These systems use the SMQI protocol which Is an unsupported feature in FlexGroup

Correct Answer: A

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 2

Your customer complains about missing volume snapshot copies on a SnapMlrror destination. While investigating this case, you notice an executed SnapMirror resync operation in the event logs of the system.
In this scenario, what Is the cause of this problem?

A. Newer Snapshot copies than the common snapshot that was chosen for resync were removed automatically at the destination. B. The autodelete option removed Snapshot copies before the resync. C. Snapshot copies were manually removed from the destination after the resync. D. NetApp ON TAP System Manager removed these snapshot copies due to a snapshot schedule.

Correct Answer: A

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 3

Your customer added a new DS4246 shelf to their FAS2750 single-node system and created a new aggregate on the new shelf. Two weeks later, they log into Active IQ and discover the Medium Impact error shown below.
Shelves with both connections via the same SAS path detected

Referring to the exhibit, which statement is correct?

A. In a FAS2750 system, the internal shelf is only seen on one path, and the external shelves are seen on two paths. B. Active IQ Is not aware of the shelf configuration for a single-node system. C. This situation is normal for a FA57750 single-node system. D. The cables are cabled Incorrectly on the SAS stack.

Correct Answer: D

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 4

Your customer is running a NetApp AFF A800 system with NetApp ONTAP 9.8 software and states that their NS224 shelf is not showing with the correct shelf ID. You analyze the data and the shelf shows an identification of "1.SHFHUXXXXXXXXXX." What is the cause of the reported Issue?

A. The shelf had a disk replaced too quickly. B. The shelf was cabled Incorrectly. C. The shelf has been power cycled. D. A new shelf was added to the controller.

Correct Answer: B

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 5

A customer's storage administrator Informs you about the deactivated Automatic Switchover (AUSO) feature on their MetroCluster IP environment.
What Information would you tell your customer in this scenario?

A. A faulty link automatically deactivated the AUSO feature. B. The AUSO feature is not available in Metrocluster IP installations by design. C. The AUSO feature cannot be activated due to a non-mirrored aggregate. D. This is a configuration failure, you can activate that feature for the customer.

Correct Answer: B

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 6

You are attempting to connect a NetApp ONTAP cluster to a very complex network that requires LIFs to fail over across subnets.
How would you accomplish this task?

A. Configure VIP LIFs using OSPF. B. Configure a I IF failover policy for each subnet inside a single broadcast domain. C. Configure VIP LIFs using BGP. D. Configure an equal number of UFs on each subnet.

Correct Answer: C

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 7

You notice poor performance on your FlexGroup and execute the system node run -node * flexgroup show command for more Information. You notice the "Urge" column has non-zero values.
In this scenario, which statement is true?

A. The data placement is uneven. B. The constituent volumes are completely full. C. The constituent volumes are out of Inodes. D. The aggregate is completely full.

Correct Answer: A

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Network Appliance NetApp Certified Support Engineer ONTAP Specialist - NS0-593 Exam Practice Test