NS0-510 by Network Appliance Valid Free Exam Practice Test

Question 1

Which two prerequisites must be met for the tape restore command to run successfully? (Choose two.)

A. For an incremental restore, you need all the tapes in the backup chain. B. You need a tape drive that is available and compatible with the tape to be restored from. C. You must know which tape device was used during the backup. D. For an incremental restore, you only need the last tape.

Correct Answer: A,B

Question 2

Which Data ONTAP command will show all tape information?

A. sysconfig -v B. sysconfig -m C. sysconfig -t D. sysconfig -a

Correct Answer: C

Question 3

A NetApp SnapVault solution requires a license on _____.

A. the primary system only B. neither the primary nor secondary systems C. both the primary and secondary systems D. the secondary system only

Correct Answer: C

Question 4

Open Systems SnapVault can back up primary data, which resides where? (Choose two.)

A. on network shares B. on SAN disks, both FCP and Iscsi C. Explanation: D. a NAS connected mount point E. on internal disks

Correct Answer: B,C,E

Question 5

Which statement is true about SnapVault backups replicating all of the file permissions and access control lists held by the original data?

A. Administrators can allow users to do their own restores safely. B. It allows restores by any users, due to its inherent user-friendly architecture. C. Only administrators can perform restores of user data from backups. D. Users authorized to access a file on the original file system will not have access to the backup copies of that file.

Correct Answer: A

Question 6

Which command is used to monitor SnapVault snapshot creation and deletion?

A. snapvault status B. snap sched C. snap list D. snapshot list

Correct Answer: C

Question 7

What are six key activities performed during the discovery phase for SnapVault-based backup recovery solution implementation? (Choose six.)

A. establish retention periods and backup schedules for each dataset B. develop a design to meet the backup requirements C. configure and activate SnapVault D. record change rates for each dataset requiring backups (per day or hour) E. identify datasets for backup F. acquire RPO granularity and RTO for each dataset for local and remote backups G. review existing backup infrastructure and backup applications in use H. record existing network infrastructure and available network bandwidth for backups

Correct Answer: A,D,E,F,G,H

Question 8

Which three data protection solutions use Snapshot technology as the underlying foundation? (Choose three.)

A. NDMP backup B. SnapVault C. SnapMirror D. SnapClone E. Flash Cache

Correct Answer: A,B,C

Question 9

The SnapMirror source controller binds on which default port?

A. 443 B. 80 C. 10566 D. 22

Correct Answer: C

Question 10

You have just completed the deployment of a NetApp data protection solution for a customer's data center. You want to show the customer how to use NetApp OnCommand System Manager to see a display of the raw and actual storage capacity they have just purchased. Which utility in the NetApp OnCommand System Manager interface shows raw and actual storage capacity?

A. Volumes B. Aggregates C. Disks D. LUNs

Correct Answer: C

Question 11

Which hardware technology is positioned in the NetApp backup and recovery portfolio?

A. Virtual Tape Library B. ReplicatorX C. SnapVault for NetBackup D. EnterpriseVault

Correct Answer: A

Question 12

You have installed SnapProtect and DataFabric Manager software on two different Windows 2008 R2 servers, which are NOT configured with Windows failover cluster services. The DataFabric Manager host fails. Which three parts of your SnapProtect solution are no longer working? (Choose three.)

A. local Snapshot copies using the SnapProtect UI B. restore of mirrored data using the SnapProtect UI C. restore of data using the storage command line D. disk-to-tape backup E. disk-to-disk backup

Correct Answer: A,B,E

Question 13

For a new _____ SnapMirror relationship, you must create the destination _____ before initializing the relationship.

A. volume; volume B. volume; qtree C. qtree; qtree D. aggregate; volume

Correct Answer: A

Question 14

Which SnapMirror relationship should you create in the snapmirror.conf file for a SnapManager for Exchange configuration?

A. filer1:vol1 filer2:vol1 - * * * * B. filer1:vol1 filer2:vol1 * * * * * C. filer1:vol1 filer2:vol1 - 15,30 * * * D. filer1:vol1 filer2:vol1 - - - -

Correct Answer: D

Network Appliance NCIE - Backup and Recovery Implementation Engineer - NS0-510 Exam Practice Test