EMC Dell PowerEdge Professional - DCPPE-200 Exam Practice Test

An engineer is inventorying a newly arrived M1000e shipment that will be used for a virtual environment. The inventory includes the following:
Blade Server Enclosure, M1000E, PowerEdge - qty 1
Power Supplies 2700W High Efficiency - qty 3
Redundant Chassis Management Controller- qty 1
Power Cords, QTY3, 8FT, C19/C20 for M1000E Server Blade Chassis - qty 2 Cat5e Patch Cable 1000Mb - qty 2 Dell Force10 MXL 10/40 GbE DCB Blade Switch - qty 2 QSFP+ 40GbE Module, 2 port, Hot Swap - qty2 SFP+ 10GbE Module, 4 port, Hot Swap - qty 2 SFP+ to SFP+, 10GbE, Copper Twinax Direct Attach cable, 3 Meters - qty 8 The chassis power will be set for grid redundancy. The top of rack switches are 10Gb and the management switch is 1000 Base-T. What is missing from this inventory that is needed to accomplish this task?

An engineer is installing a server node with a quad port 1GbE NIC into SLOT 3 on a VRTX chassis with a
1GbE Pass-Through Module (PTM) in Fabric A.
During POST of this server, a message indicates that ports 3 and 4 of the NIC are being disabled. The system completes the boot process and is otherwise operational.
What is causing this message?

An engineer is performing system updates on a large number of systems using OpenManage Essentials. The engineer has been instructed NOT to update network adapter firmware at this time.
How can the engineer exclude a firmware update while still using the Dell Online Catalog source?

An engineer is installing a known good PCIe storage adapter in SLOT 1 of an FX2 chassis with four half height nodes. Node 1 is NOT detecting the adapter.
What must the engineer do so that node 1 can detect the adapter?

A VRTX has the following physical disks:
- 8 300 GB SSDs
- 10 300 GB 15,000 rpm HDDs
An engineer needs to create two virtual disks for a file server: a system volume and a data volume.
The customer wants to maximize performance of the system volume and maximize redundancy of the data volume.
The customer also wants both virtual disks to survive one drive failure without the customer's intervention.
Which option is most appropriate to meet the requirements?

An engineer needs to update BIOS in the following environment:
- Over 100 servers are spread over 10 chassis
- All servers are in the same data center
- The only maintenance window is late Sunday evening when OS patches are applied and servers are rebooted
- Less than 10 minutes of additional downtime per server is allowed
What is the most effective update strategy?

An engineer has a new blade chassis that is 3/4 full. The chassis has six power supplies. The chassis at peak power usage needs at minimum four power supplies. Redundancy is NOT a concern.
The engineer needs a policy to meet the current needs and provide enough power to a fully populated chassis.
Which policy should the engineer choose?

An engineer needs to configure a redundant CMC network link into to a newly installed FX2 chassis. CMC port 1 is up and working. The engineer only has one management switch available for CMC connections. The engineer plugs CMC port 2 into the management switch and leaves the data center. The network engineer reports extreme traffic on the network and is unable to connect to any other switches.
How should the engineer fix this problem quickly and maintain redundancy?

An engineer needs to perform hardware configuration, including RAID, on a new batch of 30 identical server nodes. OpenManage Essentials is installed, and the sever nodes have been discovered via iDRAC.
The engineer needs the most efficient way to replicate the configuration from a single configured system without losing connectivity to the iDRAC.
How should the engineer perform this task?

Refer to the exhibit.
An engineer sets up FCoE boot on their server. The server fails during post.
What needs to be added to the NIC settings/option ROM to make booting successful?