CTS by AVIXA Valid Free Exam Practice Test

Question 1

While replacing a lamp in a client's LCD projector, it is important to:

A. Calculate the new projector throw distance. B. Test the projector using a commercially produced DVD movie. C. Measure the projector's light output with the new lamp in place. D. Clean the air filter and reset the lamp timer.

Correct Answer: D

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 2

For a design-bid (tender)-build project, the final step for determining the owner's costs for an AV system is

A. selecting an Integrator. B. ensuring the equipment specification is ready for bid. C. having the owner approve the design. D. performing a needs analysis.

Correct Answer: B

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 3

What device should be used to send a single video signal to several monitors?

A. Frame synchronizer B. Distribution amplifier C. Passive switcher D. Matrix mixer

Correct Answer: B

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 4

A client wants to replace an older projector with a flat-panel 240 in (610 cm) diagonal display. The client has complained about the cost of replacement lamps for the existing projector as the reason for switching to a flat- panel display. Which of the following is the BEST alternative for a successful solution?

A. Laser projector B. Custom-built OLED display C. Direct view LED D. LCD display

Correct Answer: C

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 5

What would be the BEST way to verify proper performance of a CAT cable fitted with a new termination?

A. connect the cable to a reference unit to check against it B. connect the source and sync, then verify there is a picture C. use a multimeter to test if the pins have a connection D. use a cable tester and run a protocol

Correct Answer: D

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 6

Before confirming an anticipated completion date with the customer, it is MOST important to

A. create the system maintenance schedule. B. ensure no components are backordered. C. double check the floor finishes. D. ensure the date is not a holiday.

Correct Answer: B

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 7

During project delivery and after completion, it is important to ensure correct management of control system code so that

A. sub-contract programmers submit uncompiled code as per their contract of employment. B. the most up-to-date version of code is available for upload when required. C. other contractors are unable to reuse or edit code. D. programming costs will be within project budget.

Correct Answer: B

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 8

Which section of the Ohm's Law chart would you use to calculate watts? Select the coned quadrant.

Correct Answer:

Explanation:
To calculate watts (P) using the Ohm's Law chart, you would use the sections that involve power formulas.
These sections are:
* P = V * I
* P = I² * R
* P = V² / R
These formulas show the relationship between power (watts) and the other electrical quantities: voltage (V), current (I), and resistance (R).

Question 9

The MOST important information to come away with from an initial site survey is the

A. final budget for the entire project. B. key decision maker. C. overall scope AV solution needed. D. manufacturers which will be used in the AV system.

Correct Answer: C

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 10

A client setting terms for "tire protection of existing conditions" would most likely apply to which of tire following project types?

A. New construction B. A prefabricated building C. A technology refresh D. Expansion of an existing building

Correct Answer: D

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 11

The integrator gets an urgent service call from the client's AV engineer that there is no power indication on the HDMI switcher in the rack. What is the BEST workaround that the integrator can suggest?

A. call the manufacturer for support B. change the power supply of the faulty unit C. patch the Input to the output, bypassing the switcher D. bring in another switcher to replace the broken one

Correct Answer: C

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 12

According to the Gantt chart pictured, the Project Manager should wait to start Activity C until which predecessor has been reached?

A. Activity B B. Week 3 C. Milestone X D. Week 4

Correct Answer: C

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 13

Which of the following is an EQ type?

A. gate B. parametric C. compressor D. limiter

Correct Answer: B

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

Question 14

After there is an approved labor change to a project, what should the project manager do NEXT?

A. update the schedule B. order the equipment C. issue an invoice for the change D. inform the purchasing department

Correct Answer: A

Explanation: Only visible for ExamsLabs members. You can sign-up / login (it's free).

AVIXA Certified Technology Specialist - CTS Exam Practice Test