7004.1 by Avaya Valid Free Exam Practice Test

Question 1

The Satellite Link Control feature ensures that the configuration of a call does not include more than one communications satellite trunk. Tandem trunk calls, when connected through more than one communication satellite trunk, are subject to transmission distortion due to propagation.
Which parameters are required to be equipped or configured for Satellite Link Control in the Communication Server 1000?

A. Network Transfer (NXFR) package must be equipped.
Route must be configured with ESN2 or ESN3 signaling
Route must be designated as a satellite route. B. Network Signaling (NSIG) package must be equipped.
Route must be configured with ESN3 or ESN5 signaling.
Route must be programmed with a Traveling Class of Service (TCOS) C. Network Signaling (NSIG) package must be equipped.
Route must be configured with ESN3 signaling.
Route must be designated as a satellite route. D. Route must be configured with STD or ETN signaling.
Route must be designated as a satellite route.

Correct Answer: C

Question 2

Click the Exhibit button.

A customer's dialing requirement, listed below, require that all station users assigned an NCOS of 3 and Class of Service of Conditionally Toll Denied (CTD) be able to place toll calls from the United States to Australia.
Australia Country Code: 61
NCOS of 3 has an FRL of 3
Expensive Routers are not being used
With reference to the exhibit, which table will allow all station users to be able to place these toll calls?

A. Provisioning Table B B. Provisioning Table D C. Provisioning Table C D. Provisioning Table A

Correct Answer: A

Question 3

An administrator is programming an NRS for the first time on a new Communication Server 1000 system RIS. 7.0 system. When attempting to add the Service Domain, it cannot be added as the Add button is grayed out in the NRS.
Which tasked should you perform to resolve this issue?

A. reinstall the NRS software B. reinstall the Signaling Server Software C. switch from Standby database to Active database D. switch from Active database to Standby database

Correct Answer: D

Question 4

Click the Exhibit button.

Consider a company's dialing plan shown in the exhibit and an example for its requirements:
A station user at the company, with Location Code 221, placed an ESN call, dialing 7-2212581. This would be an On-Net call and the NARS programming must remove the LOC code and dial the DN internally.
What programming would remove the location code for a call dialed within the originating Communication Server 1000 to a DN on that same Communication Server 1000?

A. Each site would have its own Location Code programmed as a Home Location Code (HLOC) under Translation Table #1 in their CS 1000. B. Each site would have the Location Codes for all sites programmed as Home Location Codes (HLOC) in Translation Table #1 of their CS 1000. C. Home NPA Codes (HNPA) for each site would be programmed under Translation Table #1 at each location in their CS 1000. D. The location codes for each site would be programmed under the LOC programming in Translation Table #2 at all locations.

Correct Answer: A

Question 5

Click the Exhibit button.

Consider the a customer's dialing plan shown in the exhibit, which detail on-net and off-net dialing requirements:
TIE trunks between Location A and Location B are currently out of service.
TIE trunks between Location B and Location D are currently out of service.
All over TIE trunks are fully functional.
Which route will a call to LOC 304-2001 take if it originates from location B?

A. TIE BD to Location D, then TIE CD to Location C then TIE AC to Location A B. The call will not leave the originating PBX C. TIE BD to Location D. D. TIE AB to Location A.

Correct Answer: B

Question 6

Click the Exhibit button.

A customer has a Communication Server 1000 RIs. 7 x system with System Manger / Unified Management (UCM) enabled. They have requested the addition of two new UCM Administrator User with the limited ability to provision telephones at each site. Refer to the exhibit for the roles current existing in the system.
Which action can the Network Administrator take to add these new accounts per the customer's requirements?

A. Change the built-in MemberRegister role to add the permissions required to allow telephone configuration. B. Assign the new users to the built-in NetworkAdministrator role because it has the permissions that allow telephone configuration. C. Change the built-in role Patcher role to remove all permissions except those that allow telephone configuration. D. Add a new TelephonyAdmin role with the specific permissions required to allow telephone configuration.

Correct Answer: D

Question 7

Click the Exhibit button.

A customer requires that Distinctive Ringing on a route be allowed.
Which programming within the Customer Data Block (LD 15) indicates the number of times the call receive a distinctive ring before redirection?

A. CRTO, CRT1, and CRT2 B. DFN0, DFN1, and DFN2 C. RNGO, RNG1, RNG2 D. FNA0, FNA1, and FNA2

Correct Answer: B

Avaya Communication Server 1000 for Avaya Aura® Maintenance - 7004.1 Exam Practice Test